리퍼비시 계측기

리퍼비시 계측기

Type 4602B

  • ModelType 4602B
  • MakerB&K
  • DescriptionTelephone Test Head — Type 4602B
  • Rental문의요망
  • Stock문의요망

Telephone Test Head Type 4602 B allows accurate and repeatable positioning and subsequent measurement of a telephone handset in the standardized LRGP, HATS and AEN positions as recommended by the ITU-T, as well as in the REF position (OREM A).
It is used as a general test jig with other Brüel&Kjær measurement equipment. Type 4602 B has been updated to accommodate handsets with antennas. An upgrade kit is available
for updating earlier Test Heads Type 4602.

SPEAKING POSITIONS:
LRGP position (ITU-T Rec. P.76)
HATS position (ITU-T P.58)
REF position (OREM A)
AEN position (ITU-T Rec. P.76)
PRECISION OF SPEAKING POSITIONS:
The position of the mouth reference point is within 1mm of the nominal position in the mouth axis
direction, and within 2mm of the nominal position
perpendicular to this (i.e., mouth radially)
HANDSET GAUGE FOR SYMMETRICAL
HANDSETS:
Has a 10 to 40 mm scale with 1 mm graduations
for reading the distance from the centre of the
earcap to the top of the handset
HANDSET GAUGE FOR NON-SYMMETRICAL
HANDSETS:
The maximum lateral offset adjustment range of
the handset is ±18 mm with respect to the Ear
Reference Point.
Note: The adjustment range is reduced as the
handset approaches the maximum allowable
handset width (65 mm).
In the longitudinal direction the adjustment range
is 22 mm with respect to the Ear Reference
Point.
END STOP:
Can be adjusted from 13 to 38 mm relative to
the centre of the coupler hole ring. Maximum
length of handsets from the centre of the earcap
to the top of the handset is 47 mm without the
stop screw, and 59 mm without the rear alignment rods
HANDSET ALIGNMENT RODS:
Two adjustable self-centring rods for positioning
handsets. Maximum allowable width of handsets
is 65 mm
HANDSET ALIGNMENT RODS WITH OFFSET
ADJUSTMENT:
Two sets of adjustable rods for positioning handsets. The rods are individually adjustable to accommodate asymmetrical handsets. Adjustment
range from 10 to 33 mm
COUPLER HOLE RING (40mm hole):
For earcaps with concavity from 0 to 3.9 mm
(measured at edge of IEC ear). Has a 0 to
20 mm scale (1 mm graduations) along the periphery, and a 20 to 36 mm scale under the stop
screw
COUPLER HOLE RING (50mm hole):
For earcaps with concavity from 0 to 7.0 mm
(measured at edge of IEC ear). Has a 0 to
25 mm scale (1 mm graduations) along the periphery, and a 25 to 36 mm scale under the stop
screw
HOLDER ARM:
Has a calibrated scale for adjusting the force on
the handset from 10 to 28 N (2 N graduations).
Accommodates handsets up to 55 mm height
EAR FORCE:
The force that the Artificial Ear exerts against
an earcap can be adjusted from 0 to 10 N
MOUNTING OF TEST HEAD FOR QUALITY
CONTROL:
The upper main plate (for holding the handset)
has four 5 mm threads for mounting a custombuilt handset jig.
The lower main plate (for holding the Mouth Simulator) has four 5 mm threads for mounting the
Test Head in a quality control setup.
The holder arm has a 5 mm thread for mounting
an alternative holder pad
DIMENSIONS:
Height: 430 – 468 mm (16.9 – 18.4 in)
Width: 170 mm (6.7 in)
Depth: 260 mm (10.2 in)
Weight: 5.4 kg (11.9 lb.)
Weight: 7.4 kg (16.3 lb.) with Mouth Simulator

    회사명

    부서명

    구매문의판매문의렌탈문의수리문의교정문의

    전화상담방문상담견적서상담

    문의 및 요청내용 *

    개인정보 수집, 이용 및 처리방침

    - 수집항목: 이름, 연락처, 이메일, 주소
    - 수집/이용목적: 견적요청에 대한 접수 및 결과 회신
    - 이용기간: 원칙적으로 개인정보 수집 및 이용목적이 달성된 후에는 해당 정보를 지체 없이 파기합니다.
    단, 관계법령의 규정에 의하여 보전할 필요가 있는 경우 일정기간 동안 개인정보를 보관할 수 있습니다.

    그 밖의 사항은 (주)누비콤 개인정보취급방침을 준수하며 견적서를 요청하면 개인정보처리방침에 동의하는 것으로 간주됩니다.

    • 개인정보처리방침에 동의합니다.